As Per Is : 2202 (Part -1):1999

Flush Doors

Swadesh flush Doors are a wide range of elegant doors made by a mechanized manufacturing process which offers uniform thickness without any undulation. They provide all the key functions of a top quality door including security, protection from weather, privacy and status value which comes with their good look. Flush Doors are manufactured from specially selected & well seasoned pine/hardwood timber. Solid block beard core is framed with seasoned pine/hard wood battens in kiln seasoned stiles & rails and strengthened by a layer of Cross-brands. Gurjan face veneers encompass both sides of the core. All these are bonded high pressure and temperature, with phenol formaldehyde synthetic resin as per IS:848 and permanent type preservatives, under the cross-bonding process.

Features:

Uniform thickness and smooth for lamination.
No warping, bending, bulging, shrinkage, brittleness and cracks.
Sufficient strength in both horizontally and vertically to prevent sagging and deformation under load or impact on slamming as well as resistance to normal knocks and blows.
Dimensional accuracy and stability in varying humidity.
Adequate provision for fixing the lock and screwing the hinges.
High screw holding capacity.
Totally resistant to termite and borers.
Available in BWP & MR grades both Decorative & Nondecorative type.
Thickness : 25mm, 30mm, 32mm, 35mm
Standard sizes (ft) : Normally the size in made as per the order which varies.

Technical Specification:

Sl. No. Test Prescribed in IS: 2202 (Part-I), 1999 Minimum Value for Conformity Observed Value
1.

Dimension & squareness test as per IS:4020 (Part-2), 1998

Height & width shall be measured within an accuracy of 1.0 mm

Within specified limit
2.

General flatness test as per IS:4020 (Part-3), 1998

Squareness shall be measured to an accuraty of 1.0 mm

Within specified limit
3.

Local planeness test as per IS:4020 (Part-4), 1998

Planeness will be measured an accuracy of 0.1 mm

Within specified limit
4.

Impact indentation test as per IS:4020 (Part-5), 1998

Indentation will be measured to an accuracy of 0.1 mm

Within specified limit
5.
Flexure test as per IS:4020 (Part-6), 1998
The deflections will be measured to an accuracy of 0.1 mm
Within specified limit
6.
Edge loading test as per IS:4020 (Part-7), 1998
The deflections will be measured to an accuraty of 0.1 mm
Within specified limit
7.
Shock resistance test as per IS:4020 (Part-8), 1998
4 to 5 shock/min7
Within specified limit
8.
Buckling test as per IS:4020 (Part-9) 1998
Deformation is measured to an accuracy of 1 mm, 5 min. after application of the load and 15 min after unloading
Within specified limit
9.
Slamming test as per IS:4020 (Part-10) 1998
50 times on the nail at the rate of 4-5 drops/min
Found O.K.
10.
Misuse test as per IS:4020 (Part-11) 1998
It should pass after applying 200 N force to the handle at right angle to the plane of the frame.
Satisfacory
11.
Varying humidity test as per IS:4020 (Part-12), 1998
Deviation shall be measured to an accuraty of 1.0 mm
Within specified limit
12.
End immersion test as per IS:4020 (Part-13), 1998
These shall be no de-lamination
No de-lamination found
13.
Knife test as per IS:4020 (Part-14), 1998
Minimum pass standard
Excellent
14.
Glue adhesion test as per IS:4020 (Part-15), 1998
These shall be no de-lamination
No de-lamination found
15.
Screw withdraw test as per: IS 4020 (Part-16), 1998
Applied load shall be 2.0 mm per min for complete withdrawal of the screw withing specified limit
Within specified limit

Contact Information:

Call for Help:

+91 7501386290
+91 7501386291

Mail for information:

Swadeshplywoods@gmail.com
Swadeshply.mkt@gmail.com

Submit Form: