Swadesh®

flush Doors

SWADESHPLYWOOD
flush-door

FLUSH DOORS AS PER IS : 2202 (PART -1):1999

Swadesh flush Doors are a wide range of elegant doors made by a mechanized manufacturing process which offers uniform thickness without any undulation. They provide all the key functions of a top quality door including security, protection from weather, privacy and status value which comes with their good look. Flush Doors are manufactured from specially selected & well seasoned pine/hardwood timber. Solid block beard core is framed with seasoned pine/hard wood battens in kiln seasoned stiles & rails and strengthened by a layer of Cross-brands. Gurjan face veneers encompass both sides of the core. All these are bonded high pressure and temperature, with phenol formaldehyde synthetic resin as per IS:848 and permanent type preservatives, under the cross-bonding process.

Features:

  • Uniform thickness and smooth for lamination.
  • No warping, bending, bulging, shrinkage, brittleness and cracks.
  • Sufficient strength in both horizontally and vertically to prevent sagging and deformation under load or impact on slamming as well as resistance to normal knocks and blows.
  • Dimensional accuracy and stability in varying humidity.
  • Adequate provision for fixing the lock and screwing the hinges.
  • High screw holding capacity.
  • Totally resistant to termite and borers.
  • Available in BWP & MR grades both Decorative & Nondecorative type.
  • Thickness : 25mm, 30mm, 32mm, 35mm
  • Standard sizes (ft) : Normally the size in made as per the order which varies.

TECHNICAL SPECIFICATION

Sl. No Test Prescribed in IS: 2202 (Part-I), 1999 Minimum Value for Conformity Observed Value
1. Dimension & squareness test as per IS:4020 (Part-2), 1998 Height & width shall be measured within an accuracy of 1.0 mm Within specified limit
2. General flatness test as per IS:4020 (Part-3), 1998 Squareness shall be measured to an accuraty of 1.0 mm Within specified limit
3. Local planeness test as per IS:4020 (Part-4), 1998 Planeness will be measured an accuracy of 0.1 mm Within specified limit
4. Impact indentation test as per IS:4020 (Part-5), 1998 Indentation will be measured to an accuracy of 0.1 mm Within specified limit
5. Flexure test as per IS:4020 (Part-6), 1998 The deflections will be measured to an accuracy of 0.1 mm Within specified limit
6. Edge loading test as per IS:4020 (Part-7), 1998 The deflections will be measured to an accuraty of 0.1 mm Within specified limit
7. Shock resistance test as per IS:4020 (Part-8), 1998 4 to 5 shock/min7 Within specified limit
8. Buckling test as per IS:4020 (Part-9) 1998 Deformation is measured to an accuracy of 1 mm, 5 min. after application of the load and 15 min after unloading Within specified limit
9. Slamming test as per IS:4020 (Part-10) 1998 50 times on the nail at the rate of 4-5 drops/min Found O.K.
10. Misuse test as per IS:4020 (Part-11) 1998 It should pass after applying 200 N force to the handle at right angle to the plane of the frame. Satisfacory
11. Varying humidity test as per IS:4020 (Part-12), 1998 Deviation shall be measured to an accuraty of 1.0 mm Within specified limit
12. End immersion test as per IS:4020 (Part-13), 1998 These shall be no de-lamination No de-lamination found
13. Knife test as per IS:4020 (Part-14), 1998 Minimum pass standard Excellent
14. Glue adhesion test as per IS:4020 (Part-15), 1998 These shall be no de-lamination No de-lamination found
15. Screw withdraw test as per: IS 4020 (Part-16), 1998 Applied load shall be 2.0 mm per min for complete withdrawal of the screw withing specified limit Within specified limit